FluorPure-L Series Hydrophilic PTFE Pleated Filter Cartridge with High Flow Rate and Strong Chemical Compatibility

Request a Quote
Item No Product Name Description
CRPTFEL0050206PS FluorPure-L Series Cartridge Medium: PTFE, Pore Size: 0.20μm, Length: 5inch, OD: 69mm, Adapter Type: 226/Fin, Sealing: FEP Encapsulated Silicone Request a Quote
CRPTFEL0100100S FluorPure-L Series Cartridge Medium: PTFE, Pore Size: 0.10μm, Length: 10inch, OD: 69mm, Adapter Type: DOE, Sealing: Silicone Request a Quote
CRPTFEL0100202F FluorPure-L Series Cartridge Medium: PTFE, Pore Size: 0.20μm, Length: 10inch, OD: 69mm, Adapter Type: 222/Flat, Sealing: FKM Request a Quote
CRPTFEL0100802PV FluorPure-L Series Cartridge Medium: PTFE, Pore Size: 0.80μm, Length: 10inch, OD: 69mm, Adapter Type: 222/Flat, Sealing: FEP Encapsulated FKM Request a Quote
CRPTFEL0200203F FluorPure-L Series Cartridge Medium: PTFE, Pore Size: 0.20μm, Length: 20inch, OD: 69mm, Adapter Type: 222/Fin, Sealing: FKM Request a Quote
CRPTFEL0200452S FluorPure-L Series Cartridge Medium: PTFE, Pore Size: 0.45μm, Length: 20inch, OD: 69mm, Adapter Type: 222/Flat, Sealing: Silicone Request a Quote
CRPTFEL0300206PV FluorPure-L Series Cartridge Medium: PTFE, Pore Size: 0.20μm, Length: 30inch, OD: 69mm, Adapter Type: 226/Fin, Sealing: FEP Encapsulated FKM Request a Quote
CRPTFEL030H10TPV FluorPure-L Series Cartridge Medium: PTFE, Pore Size: 10μm, Length: 30inch, OD: 69mm, Adapter Type: 222/Fin with 3 bayonet, Sealing: FEP Encapsulated FKM Request a Quote
CRPTFEL0400450F FluorPure-L Series Cartridge Medium: PTFE, Pore Size: 0.45μm, Length: 40inch, OD: 69mm, Adapter Type: DOE, Sealing: FKM Request a Quote
CRPTFEL0500457S FluorPure-L Series Cartridge Medium: PTFE, Pore Size: 0.45μm, Length: 50inch, OD: 69mm, Adapter Type: 226/Flat, Sealing: Silicone Request a Quote

Description

FL series PTFE pleated filter cartridge is made of hydrophilic PTFE membrane, which can be used for filtration of various strong acid and alkali and oxidizing solutions without pre-wetting.

Features

  • Extensive chemical compatibility

  • Good corrosion resistance, oxidation resistance, heat resistance

  • High porosity PTFE membrane, no pre-wetting required

  • High flux, low precipitation, low pressure difference

  • 100% integrity test ensures the effect of sterilization

Applications

  • Filtration of high temperature and high viscosity solvents

  • Filtration of strong acid liquid

  • Filtration of strong oxidizing liquid

  • Filtration of high-purity chemicals

  • Filtration of LVP

  • Filtration of biological reagents

Technical Parameters

Materials of Construction

Filter Membrane

Hydrophilic PTFE

Support/Drainage

PP

Cage/End Cap

PP

Core

PP/316L Stainless Steel

Adaptor

PP/PP+Stainless Steel

O-rings

S/E/N/F

Sealed by hot-melt welding, no adhesive

Filter Dimensions

 

Outer Diameter

69mm

Inner Diameter

33mm

Length

5-40inches

Filtration Area

≥0.36m² (5inches)

≥0.74m²/10inches

Operating Conditions

Maximum Differential Pressure (forward)

5.2 bar @ 25℃,1.9 bar @ 82℃

Maximum Differential Pressure (reverse)

2.1 bar @ 25℃

Biological Safety

Endotoxins

<0.25 EU/mL

Extractables

<40 mg/10inches

Sterilizable

Steam In-place

140℃ 30min

differential pressure<0.3 bar

Autoclave

121℃ 30min

Quality Control

ISO 9001:2015 quality management system

100% integrity test

Filter cartridge is fully traceable

All materials comply with relevant requirements of CFR21

Retention Efficiency for Monodisperse PSL particles≥99.99%

Typical Liquid Flow Rates

Ordering Information

CRPTFEL

Length

Pore Size

Adaptor

Seal Material

Core

005=5"

010=10"

020=20"

030=30"

040=40"

010=0.10μm

020=0.20μm

045=0.45μm

100=1.0μm

 

0=DOE

1=222/Flat with 316L SS insert

2=222/Flat

3=222/Fin

4=222/Fin with 316L SS insert

5=226/Fin with 316L SS insert

6=226/Fin

7=226/Flat

8=226/Flat with 316L SS insert

S=Silicone

E=EPDM

N=Nitrile

F=FKM

Blank=PP

T=Thickened PP

R=Reinforced PP

S=316L Stainless Steel

Related Products