PolyPure-D Series Multi-layer PP Pleated Filter Cartridge with Long Service Life
Request a QuoteItem No | Product Name | Description | |
---|---|---|---|
CRPPD0100106E | PolyPure-D Series Cartridge | Pore Size: 0.10μm, Length: 10inch, 226/Fin, EPDM | Request a Quote |
CRPPD0100456E | PolyPure-D Series Cartridge | Pore Size: 0.45μm, Length: 10inch, 226/Fin, EPDM | Request a Quote |
CRPPD0101003F | PolyPure-D Series Cartridge | Pore Size: 1.0μm, Length: 10inch, 222/Fin, FKM | Request a Quote |
CRPPD0103006E | PolyPure-D Series Cartridge | Pore Size: 3.0μm, Length: 10inch, 226/Fin, EPDM | Request a Quote |
CRPPD010H250E | PolyPure-D Series Cartridge | Pore Size: 25μm, Length: 10inch, DOE, EPDM | Request a Quote |
CRPPD0200204S | PolyPure-D Series Cartridge | Pore Size: 0.20μm, Length: 20inch, 222/Fin with SS insert, Silicone | Request a Quote |
CRPPD0201000E | PolyPure-D Series Cartridge | Pore Size: 1.0μm, Length: 20 inch, DOE, EPDM | Request a Quote |
CRPPD0205000E | PolyPure-D Series Cartridge | Pore Size: 5.0μm, Length: 20 inch, DOE, EPDM | Request a Quote |
CRPPD0300206S | PolyPure-D Series Cartridge | Pore Size:0.20μm, length:30inch, Adapter Type:226/Fin, Sealing:Silicone, Core:Polypropylene | Request a Quote |
CRPPD0300456S | PolyPure-D Series Cartridge | Pore Size:0.45μm, length:30inch, Adapter Type:226/Fin, Sealing:Silicone, Core:Polypropylene | Request a Quote |
Description
PPD adopts multi-layer gradient PP fiber material, which combines the advantages of depth filtration and pleated filtration, so that the filter cartridge has high dirt holding capacity and high retention efficiency. The full PP structure makes PPD series pleated filter cartridge suitable for clarification and filtration of various high-load chemicals.
Features
-
Multi-layer pore size gradient filter medium, extensive chemical compatibility
-
Combination of depth filter and pleated filter
-
High efficiency, high flux, low pressure drop, long service life
-
No fiber shedding
Applications
-
Filtration of glue, dyestuff, grinding fluid, high-load filtrate
-
Filtration of colloidal products
-
Filtration of fermentation broth and high viscosity materials
-
Prefiltration of culture media, blood products
-
Prefiltration of bottled water, draft beer ,wine
-
Fine filtration of carbonate beverages
-
Filtration of dairy products
-
High impurity water filtration
-
EDI prefilters
-
Resin capture filtration
Product Assurance
-
ISO 9001:2015 quality management system
-
Filter cartridge is fully traceable
-
All materials comply with relevant requirements of CFR21
Technical Parameters
Materials of Construction |
Filter Membrane |
PP |
Support/Drainage |
PP |
|
Cage/End Cap |
PP |
|
Core |
PP/316L Stainless Steel |
|
Adaptor |
PP/PP+Stainless Steel |
|
O-rings |
S/E/N/F |
|
Sealed by hot-melt welding, no adhesive |
||
Filter Dimensions |
Outer Diameter |
69mm |
Inner Diameter |
33mm |
|
Length |
5-40inches |
|
Filtration Area |
≥0.15m² (5inches) ≥0.30m²/10inches |
|
Operating Conditions |
Maximum Differential Pressure (forward) |
5.2 bar @ 25℃,1.9 bar @ 82℃ |
Maximum Differential Pressure (reverse) |
2.1 bar @ 25℃ |
|
Biological Safety |
Endotoxins |
<0.25 EU/mL |
Extractables |
<40 mg/10 inches |
|
Sterilizable |
Steam In-place |
121℃ 30min Differential Pressure<0.3 bar |
Autoclave |
121℃ 30min |
Typical Liquid Flow Rates
Ordering Information
CRPPD |
Length |
Pore Size |
Adaptor |
Seal Material |
Core |
005=5" 010=10" 020=20" 030=30" 040=40" |
050=0.50μm 080=0.80μm 100=1.0μm 150=1.5μm 300=3.0μm 500=5.0μm H10=10μm H15=15μm H20=20μm H30=30μm |
0=DOE 1=222/Flat with SS insert 2=222/Flat 3=222/Fin 4=222/Fin with SS insert 5=226/Fin with SS insert 6=226/Fin 7=226/Flat 8=226/Flat with SS insert |
S=Silicone E=EPDM N=Nitrile F=FKM |
Blank=PP R=Reinforced PP S=316L Stainless Steel
|