FluorPure-G Series Hydrophobic PTFE Pleated Filter Cartridge with Extremely Strong Chemical Compatibility

Request a Quote
Item No Product Name Description
CRPTFEG0050105S FluorPure-G Series Cartridge Pore Size: 0.10μm, Length: 5inch, OD: 69mm, Adapter Type: 226/Fin with SS insert, Sealing: Silicone Request a Quote
CRPTFEG0050109E FluorPure-G Series Cartridge Pore Size: 0.10μm, Length: 5inch, OD: 69mm, Adapter Type: 215/Flat, Sealing: EPDM Request a Quote
CRPTFEG0050207PV FluorPure-G Series Cartridge Pore Size: 0.20μm, Length: 5inch, OD: 69mm, Adapter Type: 226/Flat, Sealing: FEP encapsulated FKM Request a Quote
CRPTFEG0100102E FluorPure-G Series Cartridge Pore Size: 0.10μm, Length: 10inch, OD: 69mm, Adapter Type: 222/Flat, Sealing: EPDM Request a Quote
CRPTFEG0100102F FluorPure-G Series Cartridge Pore Size: 0.10μm, Length: 10inch, OD: 69mm, Adapter Type: 222/Flat, Sealing: FKM Request a Quote
CRPTFEG0100107VE FluorPure-G Series Cartridge Pore Size: 0.10μm, Length: 10inch, OD: 69mm, Adapter Type: 226/Flat, Sealing: EPDM Request a Quote
CRPTFEG0200105SS FluorPure-G Series Cartridge Pore Size: 0.10μm, Length: 20inch, OD: 69mm, Adapter Type: 226/Fin with SS insert, Sealing: Silicone Request a Quote
CRPTFEG0200200N FluorPure-G Series Cartridge Pore Size: 0.20μm, Length: 20inch, OD: 69mm, Adapter Type: DOE, Sealing: NBR Request a Quote
CRPTFEG0300206F FluorPure-G Series Cartridge Pore Size: 0.20μm, Length: 30inch, OD: 69mm, Adapter Type: 226/Fin, Sealing: FKM Request a Quote
CRPTFEG0400206S FluorPure-G Series Cartridge Pore Size: 0.20μm, Length: 40inch, OD: 69mm, Adapter Type: 226/Fin, Sealing: Silicone Request a Quote

Description

FG series PTFE pleated filter cartridge is made of high porosity hydrophobic PTFE membrane, which has the characteristics of high flux and long service life. Its broad chemical resistance makes the FG series filter cartridge particularly suitable for the filtration of a wide variety of low surface tension chemicals and gases.

Features

  • Extensive chemical compatibility

  • High porosity PTFE membrane

  • High flux, low pressure difference

  • Very high cost performance

Applications

  • Filtration of low surface tension solvents

  • Filtration of strong acid and alkali liquid

  • Filtration of strong oxidizing liquid

  • Sterilization filtration of compressed air and nitrogen

  • Sterilization filtration of fermentation tank, storage tank, batching tank

  • Filtration of solvents and disinfectants

Technical Parameters

Materials of Construction

Filter Membrane

Hydrophobic PTFE

Support/Drainage

PP

Cage/End Cap

PP

Core

PP/316L Stainless Steel

Adaptor

PP/PP+Stainless Steel

O-rings

S/E/N/F

Sealed by hot-melt welding, no adhesive

Filter Dimensions

Outer Diameter

69mm

Inner Diameter

33mm

Length

5-40inches

Filtration Area

≥0.36m² (5inches)

≥0.74m²/10inches

Operating Conditions

Maximum Differential Pressure (forward)

5.2 bar @ 25℃, 1.9 bar @ 82℃

Maximum Differential Pressure (reverse)

2.1 bar @ 25℃

Biological Safety

Endotoxins

<0.25 EU/mL

Extractables(WFI)

<15 mg/10 inches

Sterilizable

Steam In-place

140℃ 30min

differential pressure<0.3 bar

Autoclave

121℃ 30min

Quality Control

ISO 9001:2015 quality management system

100% integrity test

Filter cartridge is fully traceable

All materials comply with relevant requirements of CFR21

Bacteria (Pseudomonas diminuta) Aerosol Challenge Test TR≥108

Retention Efficiency for Monodisperse PSL particles≥99.99%

Typical Liquid Flow Rates

Typical Air Flow Rates

Ordering Information

CRPTFEG

Length

Pore Size

Adaptor

Seal Material

Core

005=5"

010=10"

020=20"

030=30"

040=40"

G10=0.01μm(gas)

010=0.10μm

020=0.20μm

045=0.45μm

100=1.0μm

500=5.0μm

H10=10.0μm

0=DOE

1=222/Flat with 316L SS insert

2=222/Flat

3=222/Fin

4=222/Fin with 316L SS insert

5=226/Fin with 316L SS insert

6=226/Fin

7=226/Flat

8=226/Flat with 316L SS insert

S=Silicone

E=EPDM

N=Nitrile

F=FKM

Blank=PP

T=Thickened PP

R=Reinforced PP

S=316L Stainless Steel

Related Products